S.E. International, Inc. P.O. Box 39, 436 Farm Rd. Summertown, TN 38483 USA 1.800.293.5759 | 931.964.3561 | Fax: 1.931.964.3564www.sein
Ulity MenuThe Ulity Menu allows the user to change default sengs for several operang parameters. Once a seng is changed, it remains in eect unle
Chapter 4: Common ProceduresSeng the Internal ClockTo set the internal clock, enter into the ulity menu, select CLOC, and press set. 1) First, the
The Inspector requires regular calibraon and careful handling to assure good measurements. Use the following guidelines to maintain the instrument pr
Ionizing radiaon Ionizing radiaon changes the structure of individual atoms by ionizing them. The ions produced in turn ionize more atoms. Substance
The Observer USB reads in Total Counts, CPM, CPS, µR/hr, mR/hr, µSv/hr and has the ability to collect, log, and perform stascal analysis on the dat
Observer USB Chart ScreenThe Observer USB Chart Screen displays a chart of the data currently collected by the aached instrument. The X AxisThe X axi
General Discussion of CalibraonIn order to have condence in the measurements taken with a radiaon detecon instrument, a calibraon must be perform
Eciency CalibraonThe Inspector can be used beyond simple detecon of contaminaon and can also be used to determine the acvity of beta- or alpha-em
Procedure (Metric Units)1. Aach the Wipe Test Plate and power on the Inspector. Make sure the Inspector is in Total/Timer mode, displaying CO
Exposure Rate CalibraonAn exposure rate calibraon correlates the number of counts in given me to the exposure rate present in that eld. This is i
Table of Contents1 Introducon 2How The Inspector Detects Radiaon 2Precauons 2 2 Features 3The Display
Built in Isotope EcienciesThe Inspector has a number of built in eciencies for specic isotopes. If you know the isotope being surveyed, then you ca
The Inspector is a highly reliable instrument. If it does not seem to be working properly, look through the fol-lowing chart to see if you can idenfy
Chapter 11: Basics of Taking MeasurementsThe Inspector will not detect neutron, microwave, RF (radio frequency), laser, infrared, or ultraviolet radia
Geiger counters can detect the four main types of ionizing radiaon: alpha, beta, gamma, and x-rays. Some detect only gamma and x-rays. Our instrument
Radiaon Measurement UnitsSeveral dierent units are used to measure radiaon, exposure and dosage. A Roentgen is the amount of X-radiaon or gamma ra
Background RadiaonNaturally occurring radiaon is always present, it includes high energy gamma rays from the sun and outer space and alpha, beta, an
Xtreme BootThe Xtreme boot oers maximum performance in a lightweight rugged soluon for using Radiaon Alert® products in the eld. The Xtreme boot i
DetectorInternal Halogen-quenched, uncompensated GM tube with thin mica window, 1.4-2.0 mg/cm2 areal density. Effective diameter of window is 45 mm (1
WARRANTOR: S.E. Internaonal, Inc., P.O. Box 39, 436 Farm Road, Summertown, TN 38483-0039, USA, (931) 964-3561ELEMENTS OF WARRANTY: S.E. Internaonal,
Or ll out the form online at http://seintl.com/calibrations/ NAME MODEL NAMECOMPANY SERIAL NUMBERADDRESSCITYSTATE, ZIP, & COUNTRY PHONE NUMBERPle
Chapter 1: IntroduconThe Inspector is a health and safety instrument that is opmized to detect low levels of radiaon. It measures alpha, beta, gamm
Chapter 2: FeaturesThe Inspector measures alpha, beta, gamma, and x-ray radiaon. It is opmized to detect small changes in radiaon levels and to hav
The SwitchesThe Inspector has two switches on the front and three buons on the end panel. Each switch has three sengs which are described below. Mod
Set Buon Figure 3 (5)The Set buon is used to set the Alert or Timer in normal operang mode and to select items in the Ulity Menu. See Chapter 3 Us
Chapter 3: OperaonStarng the InspectorBefore starng the Inspector, install a standard 9-volt alkaline baery in the baery compartment located in t
AutorangingWhen radiaon levels increase in some modes over certain preset levels, The Inspector uses autoranging, automacally changing to the X1000
To take a med count, follow these steps:1. With The Inspector operang, set the Mode switch to Total/Timer. The display shows 0 and Total in the uppe
Comentarios a estos manuales